|
|
 |
Miscellaneous
Products
|
|
"Drag Race"
Alternator Mounting
Kit
|
| If you are drag racing your LS1 equipped
F-Body and require no accessory drives, this kit is for you.
Designed to eliminate excess belt length and tensioners, this
kit leaves the alternator in the OE location with a manually
adjusted shorter belt. Works with standard diameter or smaller
diameter pulleys by simply changing belts. Machined from 6061
T6 aluminum and anodized black for corrosion resistance, all
hardware and instructions included. Note: this kit is designed
to be used with an electric water pump and no power steering
or air conditioning. Designed for use on aluminum blocks only.
May be used on early 6.0L truck blocks by drilling and tapping
one hole in the face of the block. |
| AB001 |
LS1 "Race" Alternator
Mount Kit |
$129.95
ea. |
|
Battery Relocation
Mount
Remove weight from the nose of your car
and put it where it needs to be - over the rear wheels.
This custom battery box mounts to the rear frame rail in
place of the OE spare tire. No welding required, all mounting
hardware included. Inside dimensions:
10.75"L x 7"W x 7-13/16"H. Available in Black
Hammertone or red powdercoat.
NOTE: NOT FOR USE WITH WET CELL BATTERIES UNLESS
SEALED OFF FROM INTERIOR.
BR001
- 1982-2002 F-Body - $89.95
|
|
|
|
^
< Click on pictures for fullsize images
>
|
|
Since race cars don't need air conditioning
and deleting the entire system can save almost 100 pounds,
this is a no-brainer modification. BMR's A/C delete panel
for the Fourth Generation F-Body is an easy solution to the
large hole left in the firewall once the A/C has been removed.
Made from 1/8" aluminum to keep the product lightweight
yet not flexible. Patterned after the OE A/C box and precision
laser cut to bolt on using existing mounting holes.
|
| FP003 |
1993-2002 F-Body A/C Delete
Panel |
$79.95
ea. |
|
|
|
Throttlebody Water
Bypass Kits
TB001
- LT1 engines
TB002
- LS1 engines
$19.95
free shipping in continental US
|
| GM
cars circulate hot coolant through the throttlebody to prevent
throttle blade icing in cold climate conditions. While this
works great for it's intended purpose, not many of us drive
our F-Bodies in the snow much! The cooler and denser the incoming
air, the more power the engine can create. This kit allows
you to bypass your throttlebody coolant passage to keep your
incoming air as cool as possible. Save yourself the hassle
of locating the hardware and use this pre-made kit instead.
Includes billet aluminum adaptor, hose clamps and rubber dust
caps to keep the throttlebody coolant passage clean if converted
back later. Please specify LT1 or LS1 when ordering. |
Check out the dyno results from this mod
by clicking HERE. |
Mounting Hardware Kits
$16.95
|
$16.95
|
$21.95
|
|
A-Body Control arms
|
F and G-Body Control
arms
|
F-Body Torque arms
|
| Don't use your rusty, factory bolts when
upgrading a suspension part. These are all Grade 8 fasteners
and all kits come with nylon locknuts. Torque arm bolts are
extra long to allow for thicker aftermarket mounting plates. |
|
|
Polished Radiator Support
|
|
Dress
up your engine bay with this highly polished, stainless
steel radiator support. Replaces the existing plastic support
with a stronger and better looking part that weighs the
same as the stock piece. New mounting hardware supplied
with kit. Fits all LT1 cars and turbocharged LS1
cars. Easy 20 minute install. Click on images below for
a larger picture.
|
|
|
|
|
|
|
Installed LT1 support
|
Installed LS1 support
|
Installed LS1 support
|
|
|
